Goodman 96% AFUE 100,000 BTU Single Stage Upflow Gas Furnace Heater GM9S961005CN

Description: GM9S961005CNCAUTION: In an effort to lower greenhouse gas emissions 40% by 2030, some areas of California are regulating the nitrous oxide (NOx) emissions of residential gas furnaces. Ensure that you are within compliance for your install region. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Purchases are processed on business days (Mon-Fri). Transit time can vary, shipments typically arrive anywhere from 5-15 business days.Standard Features• Heavy-duty aluminized-steel tubular heat exchanger• Stainless-steel secondary heat exchanger• Single-stage gas valve• Durable Silicon Nitride igniter• Quiet single-speed induced draft blower• Self-diagnostic control board with constant memory fault code history output to a LED• All models comply with California 40 ng/J Low NOx emissions standard• Can no longer be installed in California’s South Coast Air Quality Management District (SCAQMD) on or after October 1, 2019.• AHRI Certified; ETL ListedCabinet Features• Designed for multi-position installation —GM9S96: upflow, horizontal left or rightGC9S96: downflow, horizontal left or right• Certified for direct vent (2-pipe) or non-direct vent (1-pipe)• Easy-to-install top venting with optional side venting — GM9S96/upflow models only• Convenient left or right connection for gas and electrical service• Cabinet air leakage (QLeak) ≤ 2%• Heavy-gauge steel cabinet with durable finish• Fully insulated heat exchanger and blower section• Airtight solid bottom or side return with easy-cut tabs for effortless removal inbottom air-inlet applicationsGM9S961005CNHeating CapacityHigh Fire Input¹100,000High Fire Output¹96,100AFUE²96Temperature Rise Range (°F)30-60Vent Diameter³2"- 3"No. of Burners5Circulator BlowerAvailable AC @ 0.5" ESP3- 5Size (D x W)11" x 10"Horsepower @ 1075 RPM1Speed9Filter Size (in²) (Qty)(1) 20 x 25 (bottom) or (2) 16 x 25 (side)Electrical DataMin. Circuit Ampacity⁴16.93Max. Overcurrent Device (amps)⁵20Ship Weight (lbs)144¹ Natural Gas BTU/h² DOE AFUE based upon Isolated Combustion System (ICS)³ Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required).Vent pipe must be either 2″ or 3″ in diameter, depending upon furnace input, number of elbows, length of runand installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirementsand must be 2″ or 3″ diameter PVC.⁴ Minimum Circuit Ampacity = (1.25 x Circulator Blower Amps) + ID Blower amps. Wire size should be determinedin accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.⁵ Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size.May use fuses or HACR-type circuit breakers of the same size as noted.Notes• All furnaces are manufactured for use on 115 VAC, 60 Hz, single-phase electrical supply.• Gas Service Connection ½” FPT• Important: Size fuses and wires properly and make electrical connections in accordance with theNational Electrical Code and/or all existing local codes.• For bottom return: Failure to unfold flanges may reduce airflow by up to 18%. This could result in performanceand noise issues.• For servicing or cleaning, a 24″ front clearance is required. Unit connections (electrical, flue and drain)may necessitate greater clearances than the minimum clearances listed above. In all cases, accessibilityclearance must take precedence over clearances from the enclosure where accessibility clearances are greater.SHIPPING INSTRUCTIONS: To ensure proper on-time delivery, please follow the instructions below: Shipments will only be sent to the address listed on the Ebay order. If you have provided an incorrect address, call us immediately at (888) 944-8684. If the item has already shipped, you will be responsible for the rerouting, storage, or return of the item. Please provide a valid phone number for your order. This is required by the shipping firms so that the drivers can contact you to schedule a delivery appointment. We are unable to ship the product without this contact information. Once all the information has been received and the product has shipped, you will receive a tracking number. Major Damage: In some instances, damage may occur during the shipping process. To ensure you are protected, inspect the items very closely upon receipt. Do not personally sign or have another person sign for the item if you have not inspected and approved that the equipment is damage free. Once you sign, you have accepted that product As Is, and the trucking company is no longer liable. If there is Major Damage to your order note the damage on the Bill of Lading from the driver and refuse the shipment. Please contact us and a replacement will be sent out. If there are minor scratches or dings on the unit that you deem acceptable, you may accept the delivery but be sure to note the scratches or dents on the bill of lading before you sign for and accept the shipment. Concealed Damage: This is any damage found after accepting the shipment. In some cases, the equipment may be damaged in transit and the boxes may still look ok. It is best to remove all shipping boxes when receiving the shipment. If the driver does not allow this and damage is suspected, refuse the shipment and a replacement will be sent out. Once the shipment is accepted, unwrap and unbox all items to check for damage. We have 48 hours after the shipment is accepted to report concealed damage. Contact us as soon as possible if concealed damage is found. As long as it is reported in this 48-hour time frame a replacement can be sent out and the damaged unit(s) can be returned. To expedite a replacement unit, please contact us at (888) 944-8684 and we will get another unit shipped out as soon as possible. Prior to scheduling an installation date, ensure that all the material has been received and is in good shape. Returns Refunds will be granted if the item is returned in the same condition as shipped "NEW and in the original packaging". For any item that is returned and is either not in the original packaging or is damaged in any way, the Customer will be partially refunded at HVAC Warehouse's discretion of revised resale value. Refunds will be granted for items that have been shipped and received within 30 days of the shipment receipt date. Warranty Up-to-date warranty information can be found on the manufacturer's website. Most all Goodman equipment comes with a 5-year parts warranty out of the box that can be extended to a 10-year full parts warranty by registering the installed equipment with Goodman. The equipment needs to be installed by a qualified technician. The warranty only covers the parts of the equipment installed. It does not cover labor or refrigerant associated with the repair. Please see Goodman's website for the specifics of the warranty coverage for the equipment installed.

Price: 2088 USD

Location: Plant City, Florida

End Time: 2024-01-06T20:24:26.000Z

Shipping Cost: 0 USD